eMMC Pro V1.08 - New Features

eMMC Pro 1.08 Release Notes 

We are trying to make more powerful eMMC software with every each update
There are alof of optimizations and progres based on customers requests and demands.

1. # Detection Routines improved .
2. # SW Default Set as "12 Mhz"
3. # Format Functions added
4. # Partitioning / GP Area Partitioning features added.
5. # Config Features Added .
6. # Soft Erase Function Added .
7. # Deep Erase Function Added .
8. # UI - Full Flash mode added .
9. # UI - Partition mode added .
10. # UI - Selection USER ( ROM1 ) .
11. # UI - Selection BOOT1 ( ROM2 ) .
12. # UI - Selection BOOT2 ( ROM3 ) .
13. # UI - CID Parsing .
14. # UI - CSD Parsing .
15. # UI - Config Added .
16. # UI - GP Area Partition Settings added .
17. # New Firmware Released Version = 2016122615000000

When you first run eMMC Pro V1.08 sw will update your firmware .
With the new firmware we have implemented better detection and more features.
and makes it more stable and alot more powerful .

[Config Features Added]
We have added Format , Soft Erase , Deep Erase Function in the software 

[Soft Erase]
Provides a host explicit erase function.
The erasable unit of the eMMC is the “Erase Group”;
Erase group is measured in write blocks which are the basic writable units of the Device.
Once the erase command completes successfully, the device address range that was erased shall behave-
as if it was overwritten with all ‘0’ or all ‘1’ depending on the different memory technology.

[Deep Erase]
In addition to the Soft Erase command there is also an optional Deep Erase command.
The Deep Erase command differs from the Soft Erase command in that it requires the device to -
execute the erase operation on the memory array when the command is issued and
requires the device and host to wait until the operation is complete.

This should be executed the Deep Erase command with caution to avoid unintentional data loss.

[Solution for :]

1. # Wipe failed on MTK devices will be easily fixed with this option.
2. # Corrupt Disk not functioning will be solved such as Disks
   "not write protected" but devices can not be written firmware.

[Partitioning :]
General Purpose Area Partition, RPMB Partitions can be configured
General Purpose Partitions can be programmed by the setting the corresponding-
values defined on eMMC Pro Software and written into the Extended CSD registers
only once in the device life-cycle.

[UI Improvements : ]

[Full Flash mode : ]
When the file is selected with Full Flash Mode .
You are able to write the complete file as one and whole !

[Partition mode : ]
Partitions of the Dump File Selected will be displayed on the eMMC Pro UI
By selecting each partition and selected partitions will be written into target device .

[Frequency Set : ]
12 Mhz as Default

[Area : ]
USER ( ROM1 )
BOOT1 ( ROM2 )
BOOT2 ( ROM3 )
In order to comply among the eMMC Boxes and for easy understanding for our users .
We have identified the on the software ROM1 , ROM2 and ROM3 for each Area
There is full access (R/W) and all the features are compatible with eMMC Pro.

[CID / CSD Parsing : ]
There is alot of information is provided with the CID and CSD Values
such as Manufacturer Details , Device Configuration , Write Protection ,
Serial Number , etc.. Complete device specifications of the eMMC
Complete identification of the eMMC will be displayed in eMMC Pro UI .

[eMMC Pro Support page : ]
We are sorry we had a down time during the new year season
but we recovered everything is perfect now .
Thanks for all the feedbacks.




Thank you for all eMMC Pro Customers to keep sending us requests and suggestions .
There is a lot more to come

Best Regards
eMMC Pro Team